-
2.4GHz Point to Point Wireless Bridge Kit – Wi-Fi enables wired devices
$224.00Quick ViewHigh Speed Point-to-Point Bridge works as virtual Ethernet cable to Wi-Fi enable any wired Intercom / Camera / Speaker / Phone.
- Forget Ethernet cable, the Ubiquiti NanoStation LOCO is ideal for bridging networks or sharing broadband between buildings
- To install, place the units at either end of the network and connect both to Ethernet cables – for example, connect the first unit into your modem at location one, and connect the second into an Ethernet switch or WiFi access point at the other location
- Face both units so they point towards each other and the link is established. Simple!
- This is a transparent data-link layer bridge, not a routed bridge – this means that you are creating a virtual ethernet cable between the two facilities, making network setup incredibly simple – no routing configuration, all protocols (DHCP, DNS, etc) just work
- Management of the Ubquiti device couldn’t be easier with SSH and SNMP protocol support, as well as a very intuitive HTTP interface.
- Connect two remote locations on the one network
- Share Internet connection between buildings, remote sites, etc.
- Up to 200mW output power, 2×2 MIMO operation, 100Mbps
- Integrated AirOS web software for controlling power, bridge/AP mode, etc.
- Includes POE injector and 240V AC adaptor
- Two units required for wireless Point to Point bridge.
Surge protection should be used for all outdoor installations. Ubiquiti recommend that you use two Ethernet Surge Protectors – model ETH-SP – place one near the NanoStation and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.
-
5.8GHz Point to Point Wireless Bridge Kit – Wi-Fi enables wired devices
$296.00Quick ViewHigh Speed Point-to-Point Bridge works as virtual Ethernet cable to Wi-Fi enable any wired Intercom / Camera / Speaker / Phone.
- Forget Ethernet cable, the Ubiquiti NanoStation LOCO is ideal for bridging networks or sharing broadband between buildings
- To install, place the units at either end of the network and connect both to Ethernet cables – for example, connect the first unit into your modem at location one, and connect the second into an Ethernet switch or WiFi access point at the other location
- Face both units so they point towards each other and the link is established. Simple!
- This is a transparent data-link layer bridge, not a routed bridge – this means that you are creating a virtual ethernet cable between the two facilities, making network setup incredibly simple – no routing configuration, all protocols (DHCP, DNS, etc) just work
- Management of the Ubquiti device couldn’t be easier with SSH and SNMP protocol support, as well as a very intuitive HTTP interface.
- Connect two remote locations on the one network
- Share Internet connection between buildings, remote sites, etc.
- Up to 200mW output power, 2×2 MIMO operation, 100Mbps
- Integrated AirOS web software for controlling power, bridge/AP mode, etc.
- Includes POE injector and 240V AC adaptor
- Two units required for wireless Point to Point bridge.
Surge protection should be used for all outdoor installations. Ubiquiti recommend that you use two Ethernet Surge Protectors – model ETH-SP – place one near the NanoStation and the other at the entry point to the building. The ETH-SP will absorb power surges and safely discharge them into the ground.
-
GWN 7600LR – Long range Wi-Fi Access Point for outdoors
$215.00Quick ViewThe GWN7600LR is a powerful outdoor, long-range WiFi Access Point featuring weatherproof casing and heat resistent technology. It comes equipped with dual-band 2×2:2 MU-MIMO with beam-forming technology and a sophisticated antenna design for maximum network throughput and extended WiFi coverage range of up to 300 meters. To ensure easy installation and management, the GWN7600LR uses a controller-less distributed network management design and an embedded controller within the product’s web user interface. This allows each access point to manage a network of up to 30 GWN APs independently without needing separate controller hardware/software and without a single point-of-failure. Its easy installation and management features packed with extra coverage support and advanced performance features, make the GWN7600LR an ideal outdoor access point for mid-size wireless network deployments.
- 1.27Gbps wireless throughput and 2x Gigabit wireline ports
- Dual-band 2×2:2 MU-MIMO with beam-forming technology
- Support 802.3af and 802.3at Power-over-Ethernet (PoE/PoE+)
- Support 450+ concurrent WiFi client devices
- Up to 300-meter coverage range
- Advanced QoS to ensure real-time performance of low-latency applications
- Anti-hacking secure boot and critical data/control lockdown via digital signatures, unique security certificate/random default password per device
- Embedded controller allows GWN7600LR to auto-discover, auto-provision and manage up to 30 GWN series WiFi APs in a network
Showing all 3 results